Miele F44 fault codewhat it means and how to fix it
A technical fault, and Miele give the only reset duration they publish for an oven: 20 seconds off at the circuit breaker, not a plug.
Take care
What F44 means
Miele describe F44 in three words — there is a technical fault — and then, unusually, give you something to do about it rather than a booking link. Their remedy is to reset the message by disconnecting the appliance from the power supply for 20 seconds, switching it off via the circuit breaker, and to contact customer service only if it persists.
Two things in that instruction are worth pulling out. The duration is 20 seconds, and it is the only reset duration Miele publish for an oven anywhere. Do not substitute the 30 seconds or five minutes that circulate for other manufacturers, and do not shorten it either, because the point of the interval is to let the control electronics fully discharge rather than to satisfy a countdown.
The other is that Miele name the circuit breaker specifically. That is the right instruction for a hard-wired oven, and Miele’s manual allows for both installations — a plug at a switched socket, or a hard-wired connection through a fused connection unit or isolator — so if you cannot see a plug, the breaker or the cooker switch is where the 20 seconds happens. It is notably clearer advice than several other manufacturers manage on the same point.
What causes it
| Cause | What is actually happening | How likely |
|---|---|---|
| A transient electronic fault that a power cycle clears | The possibility Miele build the remedy around, since they offer a reset before any escalation and only route to service if it comes back. | Common |
| A genuine fault in the control electronics | What a code that survives the reset points at. Miele publish no further detail, which is consistent with a code that identifies the fault to an engineer. | Occasional |
What to try yourself
Find what isolates the oven. Miele’s manual allows either a plug at a switched socket or a hard-wired connection, so if there is no plug in sight use the cooker switch on the wall or the breaker in the consumer unit rather than pulling at anything behind the appliance.
Switch it off for 20 seconds. That is Miele’s published figure and the only reset duration they give for an oven.
Switch it back on and check whether the message has cleared. Reset the clock if it has been lost.
If F44 returns, stop resetting and book it. Miele allow one attempt and then route to customer service, and a code that keeps coming back is telling you something.
Get a qualified appliance engineer to look at your Miele F44
We do not pass enquiries to a repair firm, so there is no form here. When you book a qualified appliance engineer, tell them the make, the model and the exact code or message on the display, and ask whether they carry parts for this make — that is what turns one visit into a repair rather than a quote.
What it costs to fix
Typical repair cost
Depends on the cause
Time on site
5 minutes
Nothing if the reset holds. If it does not, expect a Miele diagnostic visit before any repair can be priced.
Typical UK prices including parts and labour, updated September 2026. Your quote may differ.
Own this appliance and had this code? . Nothing is published until a person has read it.
Related Miele fault codes
- F55Usually simple to fixThe safety switch-off has operated after an unusually long run. Miele say the oven is ready for use again immediately — off, on, and carry on.Related: controls and clock
- F38Get it checkedAn electronic module fault. One of only two Miele oven codes with no owner remedy at all — their answer is to book a repair, and nothing else.Related: controls and clock
- F33Get it checkedThe pyrolytic door lock will not open. One of only two codes Miele’s own manual acknowledges, and the one where cutting the power is the wrong instinct.Related: same brand
- F32Get it checkedThe pyrolytic door lock will not close, so the clean cannot start. Miele have you check the seal for a foreign object, which is often the whole answer.Related: same brand
- F134Stop — call an engineerThe sensor is reading the cavity as too hot. Miele give no owner remedy for this one, and they conspicuously withhold advice they publish for a related code.Related: same brand
- F23Get it checkedThe pyrolytic clean never reached temperature, and Miele name the reason: too much loose soiling in the cavity. Clear the worst of it and run it again.Related: same brand
Own a Miele oven? Save it and its codes come first next time.
Related guides
Technical review
Not reviewed by an engineer
No engineer has read this page. Severity follows what the manufacturer publishes, and we would rather tell you that than let a byline imply a sign-off.
Sources and how we verified this
We establish the facts from the sources below and then write the explanation ourselves. We do not copy manufacturer wording and we do not host their manuals.
- Manufacturer support portal
This page has not been reviewed by an engineer, and we would rather tell you that than imply otherwise. The severity rating follows what the manufacturer publishes: where they say isolate the appliance and call someone, so do we.