Beko E07 fault codewhat it means and how to fix it
Flowmeter faulty. The machine has lost its way of counting water, which is why Beko want the valve closed.
Take care
Get a qualified appliance engineer to look at your Beko E07
We do not pass enquiries to a repair firm, so there is no form here. When you book a qualified appliance engineer, tell them the make, the model and the exact code or message on the display, and ask whether they carry parts for this make — that is what turns one visit into a repair rather than a quote.
What E07 means
E07 is a faulty flowmeter — the newest Beko manuals translate the same row as the water meter is faulty — and it is the fourth and last code Beko document. The flowmeter is a small paddle in the fill path that spins as water passes and lets the control board count how much has gone in. It is not a component most people have heard of, but it is how a modern dishwasher knows when to stop filling.
Which explains why Beko attach their strongest instruction to it. Their solution is identical to the one for the flood code: error algorithm activated, cycle ends, and if the error continues, cut off the electricity, close the valve, contact the authorised service. Only two of Beko’s four codes carry that isolation sequence, and both are about water arriving in quantities the machine cannot account for.
A machine that cannot count water has lost its primary defence against overfilling. There are usually backstops — a pressure switch, a float in the base — but they are backstops, and Beko clearly do not want you relying on them while the machine sits plumbed into the mains under your worktop. Closing the valve removes the risk entirely and costs nothing.
What causes it
| Cause | What is actually happening | How likely |
|---|---|---|
| Flowmeter failed | The literal reading. The paddle or its sensor has stopped producing a usable signal. | Common |
| Flowmeter jammed by debris or scale | Grit from the mains or limescale stopping the paddle turning freely, so the board sees no flow even though water is arriving. | Common |
| Wiring or connector fault | The signal not reaching the board rather than the meter failing. Cheaper if that is what it turns out to be. | Occasional |
| Control board fault | The board failing to read a meter that is working. Needs the machine open to distinguish. | Occasional |
Can you fix it yourself?
Stop — this needs an engineer
What it costs to fix
Typical repair cost
£80–£180
Typically £80 to £160 fitted. An inexpensive part where most of the cost is getting to it.
Typical UK prices including parts and labour, updated September 2026. Your quote may differ.
Own this appliance and had this code? . Nothing is published until a person has read it.
Related Beko fault codes
- E02Get it checkedWater outage error — the machine asked for water and none came. Beko send you to the supply and the filters first.Related: water intake
- E01Stop — call an engineerWater in the chassis. Beko’s own instruction once the code persists is to cut off the electricity and close the valve — among the bluntest wording of any brand we cover.Related: same brand
- E06Get it checkedTemperature sensor faulty. Beko tie it to a specific symptom — the code plus poor washing means get it looked at.Related: same brand
Own a Beko dishwasher? Save it and its codes come first next time.
Related guides
Common questions about Beko E07
Why does Beko want the water off for a sensor fault?
Because of what this particular sensor does. The flowmeter is how the machine counts water going in, so without it the machine has lost its main way of knowing when to stop filling. There are backstops, but Beko plainly do not want you depending on them. Closing the valve is free and removes the risk.
Is it safe to run in the meantime?
Beko say to cut off the electricity and close the valve if the error keeps appearing, and that is the answer. A dishwasher runs unattended, often overnight, plumbed straight into the mains. This is not a fault to work around.
What is a flowmeter?
A small paddle in the fill path that spins as water goes past. Counting the turns tells the control board how much water has entered. Simple, cheap, and the machine is largely blind without it.
What shows on a machine with no display?
F1 and F2 flashing together is the E07 signature in every Beko manual. The manuals disagree on the third light: the 2025 manuals print P2 flashing with F1 and F2, while the 2024 BDIN38450C and BDFN26530 manuals and the 2026 revision print F2 blinking with F1 and F2. Treat the pair F1 and F2 as the tell and check the table in your own manual for the rest.
Technical review
Not reviewed by an engineer
No engineer has read this page. Severity follows what the manufacturer publishes, and we would rather tell you that than let a byline imply a sign-off.
Sources and how we verified this
We establish the facts from the sources below and then write the explanation ourselves. We do not copy manufacturer wording and we do not host their manuals.
- Manufacturer technical and service documentation
This page has not been reviewed by an engineer, and we would rather tell you that than imply otherwise. The severity rating follows what the manufacturer publishes: where they say isolate the appliance and call someone, so do we.