Beko E8 fault codewhat it means and how to fix it
The machine asked for water and did not get enough. Beko list five things to check before calling anyone, and most of them are outside the machine.
Take care
What E8 means
Beko give E8 as "The machine may not be taking in water", and the hedged wording is deliberate — the machine cannot tell the difference between a closed tap, a kinked hose, a blocked inlet mesh and a mains supply problem, because all four look identical from inside. What it knows is that it opened the valve and the water level did not rise fast enough.
Beko’s printed remedy is a list in a sensible order: turn the taps on, check there is not a water outage, check the inlet hose connection and straighten any fold in it, clean the pump filter, and make sure the front cover is closed and locked. Note the fourth item, because it looks out of place — the pump filter is a drain component, not a fill one, but a machine that cannot empty will refuse to fill on the next step, so Beko fold the check in here.
Two things worth adding. The inlet hose has a small mesh filter at the tap end that silts up in hard water areas and is invisible unless you disconnect the hose. And low pressure counts: a tap that is on but barely running will produce E8 just as reliably as one that is off.
What causes it
| Cause | What is actually happening | How likely |
|---|---|---|
| Tap off, or only partly open | Beko name it first. Common after any plumbing work, or when the machine has been moved. | Common |
| Inlet hose kinked or crushed | Almost always behind the machine, from being pushed back against the hose. Beko say to straighten any fold. | Common |
| Inlet mesh filter silted up | A small gauze at the tap end of the fill hose. Hard water areas block these over a few years and nothing shows until you unscrew it. | Occasional |
| Mains supply interrupted or low pressure | Beko tell you to check for a water outage. A tap that trickles will produce the same code as one that is closed. | Occasional |
| Inlet valve failed | The solenoid that lets water in. Established once the supply, the hose and the mesh are all proven good. | Rare |
What to try yourself
Check the tap behind the machine is fully open, and run a nearby cold tap to confirm the house has water and decent pressure.
Pull the machine out far enough to see the fill hose. Straighten any kink and make sure the machine is not standing on it.
Turn the tap off, unscrew the fill hose at the tap end, and look at the small gauze filter in the connector. Rinse it out if it is silted.
Have a towel ready. There is water in the hose and it will come out when you undo it.Reconnect, open the tap, and check for weeping at both ends before pushing the machine back.
Clean the pump filter as well. Beko include it in this code’s remedy because a machine that cannot drain will not fill on the next step.
Get a qualified appliance engineer to look at your Beko E8
We do not pass enquiries to a repair firm, so there is no form here. When you book a qualified appliance engineer, tell them the make, the model and the exact code or message on the display, and ask whether they carry parts for this make — that is what turns one visit into a repair rather than a quote.
What it costs to fix
Typical repair cost
£0–£130
Time on site
20 minutes
Nothing for a tap, a kink or a silted mesh. A replacement inlet valve fitted is typically £80 to £130.
Typical UK prices including parts and labour, updated September 2026. Your quote may differ.
Own this appliance and had this code? . Nothing is published until a person has read it.
Related Beko fault codes
- E02Get it checkedNo inlet water, on the washer-dryer platform. Note the leading zero — this is a different code family from E8, and the two are not interchangeable.Related: water fill and supply
- E18Get it checkedBeko say E18 is an imbalanced load stopping the spin. Nearly every repair site says it is a drainage fault. Beko wrote the manual, and the remedies are completely different.Related: same brand
- E5Get it checkedBeko give E5 as a clogged pump filter. This is the drainage code that most people arrive at through E18, and unlike E18 it really does mean the filter.Related: same brand
- Padlock symbolUsually simple to fixA padlock on the display is the child lock, not a fault. Beko unlock it by holding the second and fourth auxiliary buttons together for three seconds.Related: same brand
- E03Get it checkedAbnormal water drainage on the washer-dryer platform. Beko publish a drain hose height range for this one, and getting it wrong is a common cause.Related: same brand
- U4Get it checkedThe door lock has not confirmed. Beko publish a specific unsticking sequence, and a clear line for when it means the lock has actually failed.Related: same brand
Own a Beko washing machine? Save it and its codes come first next time.
Related guides
Technical review
Not reviewed by an engineer
No engineer has read this page. Severity follows what the manufacturer publishes, and we would rather tell you that than let a byline imply a sign-off.
Sources and how we verified this
We establish the facts from the sources below and then write the explanation ourselves. We do not copy manufacturer wording and we do not host their manuals.
- Manufacturer technical and service documentation
This page has not been reviewed by an engineer, and we would rather tell you that than imply otherwise. The severity rating follows what the manufacturer publishes: where they say isolate the appliance and call someone, so do we.