Miele Electronic module fault
Miele publish the same sentence on 34 of their 51 codes: a technical fault you cannot remedy yourself. Here is what that group covers and what it is worth.
Take care
Get a qualified appliance engineer to look at your Miele washing machine
We do not pass enquiries to a repair firm, so there is no form here. When you book a qualified appliance engineer, tell them the make, the model and the exact code or message on the display, and ask whether they carry parts for this make — that is what turns one visit into a repair rather than a quote.
What this means
Two thirds of Miele’s published washing machine codes carry one identical sentence: this is a technical fault that you cannot remedy yourself, please book a repair appointment online. The codes in that group include F1, F2, F3, F4, F19, F29, F39, F43, F44, F45, F47, F49, F50, F51, F53, F63, F64, F65, F81, F83, F103, F104, F105, F106, F130, F131, F139, F140, F199, F211 to F214 and F242.
Several of them are described as electronic module faults. Rather than publishing thirty-four near-identical pages, which would tell you nothing and would be the doorway-page pattern this site exists not to produce, this one page covers the group honestly.
What is useful to know is what the classification means and does not mean. It means Miele have decided there is no safe or effective owner remedy, not that the machine is beyond repair — their engineers have diagnostic access that the code alone does not give you. It also means that any third-party page offering you a fix for one of these is going beyond what the manufacturer publishes. The one genuine exception is F41, which is also an electronic module fault and is the only one where Miele publish a power cycle. If your code is F41, use that page instead.
What causes it
| Cause | What is actually happening | How likely |
|---|---|---|
| A component fault with no owner-serviceable remedy | What the classification means. Miele have judged that no safe owner action exists rather than that the machine is finished. | Common |
| Electronic module failure | Several codes in this group are named as electronic module faults specifically, including F39, F43, F44, F45, F47, F49 and F130. | Common |
| Sensor or motor circuit fault | Others in the group point at the drive and sensing side. The code alone does not narrow it further for an owner. | Occasional |
Can you fix it yourself?
Stop — this needs an engineer
What it costs to fix
Typical repair cost
£110–£350
Time on site
10 minutes
A Miele diagnostic visit is typically £110 to £140, usually offset against the repair. An electronic module fitted runs to £220 to £350, at which point the age of the machine becomes the deciding factor.
Typical UK prices including parts and labour, updated September 2026. Your quote may differ.
Own this appliance and had this code? . Nothing is published until a person has read it.
Related Miele fault codes
- F41Get it checkedAn electronic module fault — but the only one of them where Miele publish an owner step. Switch off, wait about ten seconds, switch back on.Related: electronics and power
- 888Usually simple to fixDemo mode. The machine will not start because it is set up for a shop floor, and Miele publish the exit sequence.Related: electronics and power
- F62Usually simple to fixThe programme selector is parked between two settings. Turn it to a defined position and the code goes.Related: electronics and power
- F11Get it checkedThe drain is restricted. Miele publish a maximum drain height of one metre, and they warn that straightening a kinked hose can weaken it enough to split later.Related: same brand
- F10Get it checkedWater is not getting in. Miele point at the stopcock and the inlet filter, and both are owner jobs on their own guidance.Related: same brand
- F34Get it checkedThe door could not be locked. Miele’s manual says close the door again and restart; their website adds an overloaded drum and a two-minute power-off. Try those before calling.Related: same brand
Own a Miele washing machine? Save it and its codes come first next time.
Related guides
Technical review
Not reviewed by an engineer
No engineer has read this page. Severity follows what the manufacturer publishes, and we would rather tell you that than let a byline imply a sign-off.
Sources and how we verified this
We establish the facts from the sources below and then write the explanation ourselves. We do not copy manufacturer wording and we do not host their manuals.
- Manufacturer support portal
This page has not been reviewed by an engineer, and we would rather tell you that than imply otherwise. The severity rating follows what the manufacturer publishes: where they say isolate the appliance and call someone, so do we.