Miele F41 fault codewhat it means and how to fix it
An electronic module fault — but the only one of them where Miele publish an owner step. Switch off, wait about ten seconds, switch back on.
Take care
What F41 means
Miele publish seven or eight codes that all describe an electronic module fault, and F41 is the only one where they give you something to try. Their instruction is precise: switch the washing machine off and then back on again after approximately ten seconds, and contact Service only if it persists.
Every other electronic module code — F39, F43, F44, F45, F47, F49 and F130 among them — carries their standard sentence instead, that this is a technical fault you cannot remedy yourself and you should book a repair. That distinction is deliberate rather than an oversight, and it is the useful content on this page: Miele are telling you that F41 is the one that can be a transient state rather than a failed component. The ten seconds matters more than it looks.
Control boards hold a charge in their capacitors for a few seconds after the power goes, and a module that is stuck will still be stuck if you flick the switch off and straight back on, because it never actually lost power. Counting to ten is what makes it a real power cycle. If it comes back after that, it has stopped being a glitch and become a fault, and Miele’s advice is then the same as for all the others.
What causes it
| Cause | What is actually happening | How likely |
|---|---|---|
| Transient module state | The reason Miele publish a power cycle for this code and not the others. A momentary condition rather than a failure. | Common |
| Mains disturbance or brief supply interruption | A brownout or a spike can leave a control board in a state it cannot exit on its own. | Occasional |
| Electronic module genuinely failed | What it means if it returns after a proper power cycle. At that point Miele’s advice matches their other module codes. | Occasional |
What to try yourself
Switch the machine off. At the machine, and ideally at the socket as well.
Wait about ten seconds. Miele specify the delay and it matters — the board holds a charge for a few seconds, so a quick off-and-on is not a power cycle at all.
Switch it back on and select a programme.
If the code has gone, use the machine normally. A single transient is not a reason to book anything.
If it comes back, stop and book a Miele engineer. Repeating the cycle indefinitely will not fix a failed module.
Do not keep power cycling a machine that keeps returning the same fault. Miele offer this step once, not as a routine.
Get a qualified appliance engineer to look at your Miele F41
We do not pass enquiries to a repair firm, so there is no form here. When you book a qualified appliance engineer, tell them the make, the model and the exact code or message on the display, and ask whether they carry parts for this make — that is what turns one visit into a repair rather than a quote.
What it costs to fix
Typical repair cost
£0–£350
Time on site
5 minutes
Nothing if the power cycle clears it. A replacement electronic module fitted by Miele is typically £220 to £350, at which point the age of the machine matters.
Typical UK prices including parts and labour, updated September 2026. Your quote may differ.
Own this appliance and had this code? . Nothing is published until a person has read it.
Related Miele fault codes
- Electronic module faultGet it checkedMiele publish the same sentence on 34 of their 51 codes: a technical fault you cannot remedy yourself. Here is what that group covers and what it is worth.Related: electronics and power
- 888Usually simple to fixDemo mode. The machine will not start because it is set up for a shop floor, and Miele publish the exit sequence.Related: electronics and power
- F62Usually simple to fixThe programme selector is parked between two settings. Turn it to a defined position and the code goes.Related: electronics and power
- F11Get it checkedThe drain is restricted. Miele publish a maximum drain height of one metre, and they warn that straightening a kinked hose can weaken it enough to split later.Related: same brand
- F10Get it checkedWater is not getting in. Miele point at the stopcock and the inlet filter, and both are owner jobs on their own guidance.Related: same brand
- F34Get it checkedThe door could not be locked. Miele’s manual says close the door again and restart; their website adds an overloaded drum and a two-minute power-off. Try those before calling.Related: same brand
Own a Miele washing machine? Save it and its codes come first next time.
Related guides
Technical review
Not reviewed by an engineer
No engineer has read this page. Severity follows what the manufacturer publishes, and we would rather tell you that than let a byline imply a sign-off.
Sources and how we verified this
We establish the facts from the sources below and then write the explanation ourselves. We do not copy manufacturer wording and we do not host their manuals.
- Manufacturer support portal
This page has not been reviewed by an engineer, and we would rather tell you that than imply otherwise. The severity rating follows what the manufacturer publishes: where they say isolate the appliance and call someone, so do we.