Hotpoint oven fault codes
Hotpoint publish two oven fault codes. Not two hundred, not forty — two. For every other code their manual gives one instruction, and it is not to look the code up but to read the number down the phone. So if you are here with an F followed by a number, the honest answer is that Hotpoint have decided not to tell you what it means, and any site that appears to know is not getting it from Hotpoint. What they do document well is the other half of this: the things that look like faults and are not.
Where the code shows on a Hotpoint
The defining fact about Hotpoint oven codes is that the mapping is withheld on purpose. Their troubleshooting tables carry a row reading that the display shows the letter F followed by a number, that the cause is a software problem, and that the solution is to contact the call centre and state the number following the letter F. Ten current GB manuals were checked and not one contains a table translating those numbers. Two codes escape that treatment and get a real meaning — F3E3 and F8E8 — and both come with an owner action. Everything else is a number to read aloud. There is a second thing to know before matching anything against your manual, because one badge covers two entirely different documentation systems. The 60cm built-in single ovens carry Whirlpool-authored manuals: document numbers beginning with W, a problem and cause and solution table, and the letter-F row. The 89cm and 72cm built-in and built-under double ovens carry Beko-authored manuals in Beko house style, with numbered sections and a symptom-based troubleshooting section using a triple-arrow convention. Those Beko-lineage manuals contain no fault codes at all, not even the letter-F instruction. So whether your Hotpoint oven can show you a code depends on which half of the range it came from, and the model number is the only way to tell.
How to reset a Hotpoint
Start with the clock, because on these ovens it is not a cosmetic setting. Hotpoint state that you must set the time of day before using the oven and that if you do not, some models will not cook at all — and that a power outage cancels the setting, so it has to be done again. An oven that stopped working after a power cut with a flashing clock is the single most common non-fault in this range and it costs nothing to fix. Beyond that, be careful what you call a reset. Hotpoint document a factory reset on some models, reached through the info menu, and their own wording is explicit that all saved settings will be deleted — that is a destructive operation rather than a way of clearing a fault, and it should not be the first thing anyone tries. As for a power cycle, none of the three brands in this group publishes a duration to switch off for. We are not going to supply one. If you do isolate the oven, Hotpoint’s own installation guidance says it must be possible to disconnect it either by unplugging it, if the plug is accessible, or by a multi-pole switch upstream of the socket — so use the plug if you can reach one and the cooker switch or breaker if you cannot. Reset the clock afterwards or you will conclude the reset failed when it did not.
Most common Hotpoint faults
The Hotpoint codes people look up most.
- FGet it checkedAn F followed by a number. Hotpoint publish no meaning for any of them — their instruction is to read the number down the phone, not to look it up.
- Clock flashingUsually simple to fixOn some Hotpoint ovens the clock is an interlock, not a convenience. Until the time of day is set, the oven will not cook at all.
- KeylockUsually simple to fixNone of the buttons work. Hold the lock key for at least five seconds to release it — the oven is not broken, the panel is locked.
- DEMOUsually simple to fixDemo mode is on, so everything works except the heat. Hotpoint give a free diagnostic tell: the word DEMO appears every 60 seconds.
Every Hotpoint fault code
7 published codes. Filtering happens in the page — every one is in the HTML.
Showing 7 of 7 codes
Hotpoint models
Codes can differ between generations. Check yours.
Guides that help with Hotpoint faults
How to reset an oven: the clock, the switch, and the codes
A built-in oven has no plug, most of what it displays is not a fault, and on some models setting the clock is the reset. What each manufacturer publishes.Read the guideOven not heating: what to check before you call anyone
Many cold ovens booked for repair have a free cause: demo mode, the clock, a lock, the wall switch. The checks in order, where to stop, and what it costs.Read the guideIs an oven fault dangerous? The codes that mean stop
Two oven codes are rated dangerous here, and they need different people. What F134 and Er2 mean, how to isolate an oven with no plug, and the fire rule.Read the guide
Looking for Hotpoint’s own support? www.hotpoint.co.uk. We are not affiliated with Hotpoint.